Tag: live recording

GarageBand for iOS (iPad): Jam with other GarageBand users

GarageBand for iOS (iPad): Jam with other GarageBand users:

You can make music with other GarageBand users sharing a Wi-Fi connection. The bandleader creates a jam session, then up to three band members can join the jam session. Playback and recording are synchronized between all devices, so everyone can play and record together as a band. The leader can keep exclusive control of playback and recording, or allow all members to share control.

Gain Staging in Logic Pro — What Is It, & Does It Even Matter?

Gain Staging in Logic Pro — What Is It, & Does It Even Matter?:

There are few things that strike so much fear or disdain for Logic users than the word gain staging.

I am a firm believer in gain staging. I did it a lot setting up for recording live from a Mackie mixer. The band thought the proper way to control volume was to adjust the trim pots, never mind the faders on the board. I tried to do it every time, but that wasn’t always easy. It was the same room almost always, so the pictures I took of the mixer helped a lot.

Did the sound change when properly gain-staged? Absolutely.

Working Template

I recorded the Titan Valley Warheads a whole lot from 2014 through 2016 (like 120 nights, 200+ sets).

There’s a lot of really good music in there. I am not sure how to pull it all out.

Latest attempt was simply drag the 8 channels of audio that I captured from a Mackie 1624-VLZ3 along with a stereo front-of-house mix (they pushed it in mono, I captured in stereo — and played with the panning).

I have always struggled with ambient noise, noisy crowd, way too sensitive microphones. Latest track was kind of bad — band was not balanced, my attempts at “fixing” the sound were not fruitful. Sent the mix off to some trusted listeners (a band member and an accomplished player who understands the medium — pretty good player too! 😉 ) Got feedback. A lot like I expected, but concentrated on areas that needed focus. With so much to do I can get lost.

I have 2-track recording from the FOH (board). I have a 2-track from a mix attempt in my mixer as well. Sometimes my mixer gets like one channel, the bass, and sometimes all of it. It’s a learning process.

After comments about balance between players I went back to the board and did a critical listen. The board showed none of the problems, or at least they were very subtle. What the heck is going on? How can this happen.

I spent an afternoon just looking at the manual for the board, the picture(s) I have of the live mix, and attempted to re-create what the board did in my DAW. My raw input tracks were all post-gain, pre-EQ, so no processing through the board. Board sounds pretty darn good (kudos, Mackie).

All right. Set all the low cut, low shelf, and high shelf on the EQ. Attempt to match the mid-frequency sweep with cut/boost as required. Push some faders up on the vocals. Do some “odd” routing for vocal reverbs in the FOH mix. Playback. Whoa…so good…so much different than what I got with dry tracks. Who knew?

This is a proper starting point. Not those dry tracks. Doesn’t sound “real” yet, don’t have dumpy bar room acoustics applied, but the source sounds like the band I know. They play well. They are balanced and really enjoy what they do. It’s good to capture that and be able to get it back out . …sidetracked by Little Feat “Spanish Moon”…sorry…

Anyway. New template. 8 channels for the band. All the EQ set as close as I can tell. FX added. Post-gain fader adjustment to levels applied. Excellent starting point.

Part 2 template sends raw audio to XR18 (just like original) and plays back through XR18 mains. I can adjust each channel in the XR18.

Scenes on the XR18 for Logic to XR18 (playback) and Logic to XR18 to Logic so I can compare things from the mixer with what I get from the DAW.

Templates are a remarkable tool. Help my slow mind and slow fingers. Won’t talk about frequency-challenged hearing…

iZotope RX Mastering Tips

10 Common Uses for Audio Restoration in Mastering

4. Removing unwanted distortion Every once and a while you get a project that has audible distortion. It could be undesirable clipping, or it could be something else entirely. All you know, from your vantage point, is that the distortion is undesirable to you.

But it might not be undesirable to the band. Your first move is to call the point person on the production team and ask if that distortion is intended. If it isn’t, your next move is to contact the engineer, if you can, and negotiate a better mix. This option isn’t always on the table, so luckily software like RX has ways to fight this distortion—tools which can, to some extent, repair mangled material.

A lot of the time the De-clip module does the trick, even if the material isn’t clipping per se. The process is relatively simple: highlight the passage that is distorting, have the module suggest its processing, audition the results, and tinker to taste.

Repairing distortion is best done in specific, sporadic places, and not across passages of more than a couple of seconds—and that’s speaking liberally. You may have to spend a bit of time to get all the nasty bits, but it’s still worth it.

Sometimes, the distortion is more of a high-end crackle than a clip. Here, the De-crackle module, tuned to attenuate high-frequency distortions, can often work.

I have a very particular live performance in mind. Recorded a guitar (DI) that was using some form of distortion — pedal or amp, not sure. Unfortunately detracts from some of the songs, can’t really remove the guitar. My case isn’t mastering, I have an isolated track. Need to try the “De-crackle” and “De-clip”. The track(s) don’t clip. Challenging.

Applying in practice. As I suspected the De-clip module doesn’t touch the distorted audio. The clipping got recorded at about -12 dB soooo.

De-crackle made a nice dent in the scratchy top-end of the distortion. Basically maxed out the settings, soloed the crackles, made things better. Nice to know.